MatchMyFilter is supported by readers. When you buy through our links we may earn a commission at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more›

Samsung Refrigerator Water Dispenser Not Working

Part of our guide: Troubleshooting filter problems ๐Ÿ“Œ Key takeaways A closed door, Control Lock, and the Water setting are...

๐Ÿ“Œ Key takeaways

  • A closed door, Control Lock, and the Water setting are the first things to confirm
  • A clogged filter can cut flow or cause bad tasting water, so test with it removed on 2024 and older models
  • Trapped air after a filter change or new install often causes dripping and sputtering
  • Samsung lists 30 to 130 psi as the target water pressure range

Start with the simple checks: make sure the door is closed, Control Lock is off, and Water is selected. If those are fine, remove the water filter and try again on 2024 and older models, then check the water line and pressure. Samsung says a clogged filter, trapped air, or low water pressure are common causes of slow, silent, or dripping dispensers.

Start with the easiest checks

Before you touch any plumbing, rule out the simple settings. Samsung says models with an external dispenser will not dispense while the door is open, so close it fully and try again.

Next, confirm Control Lock is off. On most refrigerators Samsung says you turn it on and off by touching and holding Control Lock for more than three seconds. Then make sure Water is selected rather than cubed or crushed ice. Some models use a separate lever for water and ice, so check your user manual if you are unsure.

  • Close the door fully
  • Turn off Control Lock
  • Select Water, not ice
Stainless steel refrigerator in a large kitchen with a center island
Illustrative photo. Photo by Bradikan on Unsplash

Test the water filter

A clogged water filter can reduce water pressure or make water taste bad, according to Samsung. On models made in 2024 or earlier, Samsung says to remove the filter and try dispensing again. If water flows with the filter out, replace it, and use only Samsung brand filters.

Samsung notes this filter-out test is only for models made during or before 2024. Do not try it on models made in 2025 or later. If water still will not come out with the filter removed, move on to the water line checks below.

  1. Remove the water filter following your manual
  2. Try to dispense water
  3. If water flows, install a new Samsung filter
  4. If nothing flows, check the water line

Check the water line and connections

With the filter ruled out, Samsung says to confirm the water line is connected to the refrigerator, free of kinks, bends, or pinches, and turned on and open. If the doors were recently removed, check that the coupling above the door was reconnected properly.

A line that is bent at the coupler can let air in and cause dripping. Samsung says the water lines and couplers only need inspection if the problem started after the doors were removed, such as during installation or a move. If that is not your situation, skip ahead to the pressure test.

Purge trapped air

Air in the water line is a common cause of dripping and sputtering, especially after a filter change or a new install. Samsung says to dispense water into a large pitcher until it stops automatically. If the stream sputters, empty the container and dispense again, up to three more times if it keeps sputtering.

If the stream runs steady and the dripping stops, Samsung says you can assume no air is left in the line. If dripping continues, go back and check the line and couplers. Unless you have a well system, Samsung notes air rarely enters the line without a recent change like a filter replacement.

Test the water pressure

Samsung says the water line should fill 6 ounces, or 3/4 cup, in less than 10 seconds. Dispense into a measuring cup to check. If the test fails, remove the filter and run it again. Passing only without the filter points to low pressure or an old filter, so replace the filter and retest.

If both tests fail, the pressure is too low. Make sure the home water supply valve is fully open, then repeat the test. Samsung lists a target range of 30 to 130 psi and says to contact a plumber if pressure is too high. A Reverse Osmosis system can also lower pressure, so Samsung suggests a plumber for that too.

If the stream still sputters or the dispenser drips when idle, Samsung says to request service. On models with an Autofill pitcher, a leaking dispenser also calls for service.

What to check for your model

These checks come from Samsung's general dispenser guide. Exact steps, filter removal, and settings vary by model, so confirm details in your owner's manual. The guide does not cover every model, and some issues, like a missing nozzle on certain beverage center models, require contacting Samsung.

Next step

Glass pitcher and a drinking glass of water on a table
Illustrative photo. Photo by J. Brouwer on Unsplash

โ” FAQ

Why does my Samsung dispenser drip after I get water?

Samsung says a few drips for a few seconds after dispensing is normal. Leave the glass under the dispenser about 3 to 5 seconds to catch them. Samsung lists trapped air, ice buildup in the ice chute, and water pressure among the common causes of dripping.

Why is no water coming out at all?

Check the door is closed, Control Lock is off, and Water is selected. Then confirm the water line is connected, kink free, and turned on. On 2024 and older models, Samsung suggests removing the filter to test flow.

Can I test my dispenser without the filter on a 2025 model?

No. Samsung says dispensing without the water filter is only for models made during or before 2024, not for models made in 2025 or later. Follow your manual for those models.

Sources

This article was written by the MatchMyFilter editorial team from manufacturer support pages. We do not run lab tests. As an Amazon Associate I earn from qualifying purchases.

Find the right filter for your model

Samsung uses different filter codes for different models, so match the code on your current filter or your model number first. Use the filter finder to look up your model number.

Not sure which one you have? Our guide to finding your refrigerator model number shows where to look.

More on this topic: Refrigerator Water Filter Problems: Slow Water, Bad Taste, Fit and Light Issues

About the author

Ethan Marlowe
Ethan Marlowe

Ethan Marlowe is the Lead Technical Editor and Appliance Filtration Specialist at MatchMyFilter. He specializes in home appliance maintenance, water filtration mechanics, and independent verification of NSF/ANSI standards (NSF 42, 53, and 401) across major US refrigerator brands.