MatchMyFilter is supported by readers. When you buy through our links we may earn a commission at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more›

Whirlpool Side by Side Water Filter Light Won’t Reset

Part of our guide: Troubleshooting filter problems ๐Ÿ“Œ Key takeaways The status light must be reset by hand after each...

๐Ÿ“Œ Key takeaways

  • The status light must be reset by hand after each filter change
  • Reset steps differ by control panel, so match the buttons on your fridge
  • Whirlpool recommends a new filter every 6 months or when the light comes on
  • A clogged or wrongly installed filter can slow water flow and ice output

Whirlpool says the filter status light does not reset on its own, so you have to reset it manually after every filter change. The button sequence depends on your side by side model, so check your owner's manual for the exact steps.

Why the Light Stays On After a Filter Change

If you just swapped the cartridge and the Replace or Order icon is still glowing, the refrigerator is not broken. Whirlpool says the water filter status needs to be reset every time the filter is replaced, and it does not reset automatically. The light is simply waiting for you to tell it that fresh filtration has started.

That means the fix is almost always a button sequence on the control panel, not a new part. The catch is that Whirlpool builds side by side refrigerators with several different control layouts, and each one resets in its own way. Before you press anything, find your owner's manual or look closely at the buttons on your dispenser and temperature panel.

  • The light tracks filter life, not water quality
  • A manual reset is required after every cartridge change
  • Different control panels use different reset buttons
  1. 1Part on your old filterWhirlpool W10295370APrinted on the cartridge label
  2. 2Same part asEDR1RXD1 (Filter 1)Also sold as W10295370A; everydrop Filter 1
  3. 3ReplaceEvery 6 monthsSooner if flow slows or taste changes
  4. 4Before you orderMatch the part numberOn the box or listing: EDR1RXD1 (Filter 1)
How the Whirlpool W10295370A matches the EDR1RXD1 (Filter 1) filter. Diagram: MatchMyFilter, from our filter map (source: everydrop and Waterdrop Amazon listings. Fits Whirlpool, Maytag, Amana, KitchenAid and JennAir models that use Filter 1).

Reset Steps for Common Side by Side Control Panels

Whirlpool's product help page lists several reset methods for side by side refrigerators. Find the description that matches the buttons on your own fridge and follow it exactly. If none of these match, your model uses a different layout and the owner's manual is the right place to look.

  1. Options button models: press Options to enter Options mode, press Lock to start the reset, then press Measured Fill to confirm. The Order and Replace icons should disappear.
  2. Filter button models: press and hold the Filter button for 3 seconds. The Order and Replace icons should disappear when the reset finishes.
  3. Temp Setting button models: the reset button is on the control panel inside the refrigerator compartment. Press Temp Setting within 3 seconds, and the status light should change from red to off.
  4. Light and Ice Type button models: press and hold the Light and Ice Type buttons together for 3 seconds. The status light should turn off.
  5. Water Filter button models: press and hold the Water Filter button for 3 seconds. The water filter icon should return to blue and the Replace Filter message should clear.

Other Reset Combinations Whirlpool Lists

Whirlpool's page also shows a few additional reset examples that may apply to your refrigerator. On some models, you touch MAX COOL and MAX ICE at the same time for 3 seconds. The display runs a 3 second countdown, then the icon flashes and a tone plays.

Another listed method uses the Light and Ice Type buttons held together for 3 seconds, which turns the status light off once the system resets. Because Whirlpool repeats similar button names across different layouts, confirm the match against your own panel rather than guessing.

  • MAX COOL plus MAX ICE for 3 seconds on some models
  • A countdown, flashing icon and tone confirm the MAX COOL and MAX ICE reset
  • Light and Ice Type held for 3 seconds turns the light off on other models

If the Light Still Will Not Reset

Work through the possibilities in order. First, make sure the new cartridge is seated correctly. Whirlpool notes that a clogged or incorrectly installed water filter can reduce water flow to the ice maker and dispenser, which can show up as small ice cubes, low ice production or longer dispensing times.

Second, check that you are using the reset method for your exact panel. Buttons with similar names can behave differently from one layout to the next, and a sequence meant for another model will not clear the light. Your owner's manual lists the instructions for your specific refrigerator.

Third, think about timing. Some methods, like the Temp Setting reset, require you to press the button within a short window, and the hold times on the other methods are specific. If the light stays on after a careful second attempt, Whirlpool suggests contacting support or scheduling service with an approved provider.

  • Reseat the cartridge and check for slow dispensing or weak ice
  • Repeat the reset using the method for your exact control panel
  • Contact Whirlpool support or schedule service if the light persists

Keeping the Filter Light on Schedule

Whirlpool recommends replacing the water filter every 6 months, when the indicator light comes on, or as needed. On refrigerators with an indicator light, the light sits on the temperature control panel and signals when a change is due. On models without an indicator, Whirlpool suggests changing the filter at least once every 6 to 9 months.

If your filter is clogged and you cannot replace it right away, Whirlpool says you can leave it out so the water system runs in bypass mode. Water and ice will keep working without filtration, and the clogged cartridge will not slow dispensing. You will need a new filter installed to get filtered water again.

After dispensing, Whirlpool notes that one or two drops of water may be visible, which is normal, and it may help to hold your container under the dispenser for 2 to 3 seconds after releasing the button.

  • Replace every 6 months, when the light comes on, or as needed
  • No indicator light? Change at least every 6 to 9 months
  • Running without a filter puts the system in bypass mode

What to check for your model

Reset button names, locations and hold times vary by Whirlpool side by side model, and this guide only covers the examples Whirlpool lists on its product help page. It does not cover diagnosing a failed control board or dispenser, so consult your owner's manual or Whirlpool support for anything beyond these steps.

Next step

  1. 1Part on your old filterWhirlpool UKF8001Printed on the cartridge label
  2. 2Same part asEDR4RXD1 (Filter 4)Also sold as UKF8001; 4396395; everydrop Filter 4
  3. 3ReplaceEvery 6 monthsSooner if flow slows or taste changes
  4. 4Before you orderMatch the part numberOn the box or listing: EDR4RXD1 (Filter 4)
How the Whirlpool UKF8001 matches the EDR4RXD1 (Filter 4) filter. Diagram: MatchMyFilter, from our filter map (source: everydrop and Waterdrop Amazon listings; Filters Fast model pages).

โ” FAQ

Does the Whirlpool water filter light reset by itself after a filter change?

No. Whirlpool says the water filter status needs to be reset every time the filter is replaced and does not reset automatically. You have to run the reset sequence for your model.

How long should I hold the buttons to reset the filter light?

On the methods Whirlpool lists, most resets use a 3 second press or hold, such as holding the Filter button or the Light and Ice Type buttons for 3 seconds. The Temp Setting method instead asks you to press the button within 3 seconds. Check your owner's manual because the steps vary by model.

What if my side by side model is not listed here?

Whirlpool recommends consulting your Owner's Manual for the specific instructions for your model, since resetting the water filter status light varies by model and refrigerator type. If the light still will not clear, Whirlpool suggests contacting support or scheduling service.

Sources

This article was written by the MatchMyFilter editorial team from manufacturer support pages. We do not run lab tests. As an Amazon Associate I earn from qualifying purchases.

More on this topic: Refrigerator Water Filter Problems: Slow Water, Bad Taste, Fit and Light Issues

About the author

Ethan Marlowe
Ethan Marlowe

Ethan Marlowe is the Lead Technical Editor and Appliance Filtration Specialist at MatchMyFilter. He specializes in home appliance maintenance, water filtration mechanics, and independent verification of NSF/ANSI standards (NSF 42, 53, and 401) across major US refrigerator brands.