How to Replace an LG Refrigerator Water Filter
Part of our guide: Replacing and maintaining a filter ๐ Key takeaways LG recommends a new filter about every 6...
Part of our guide: Replacing and maintaining a filter
๐ Key takeaways
- LG recommends a new filter about every 6 months, or sooner if flow slows or the indicator turns on
- Place a towel or cup under the housing before removal to catch drips
- Flush roughly 2.5 gallons (9.5 liters) of water after installing the new filter
- Hold the Water Filter or Filter Reset button for 3 seconds to clear the indicator
LG says to remove the old filter by turning it counterclockwise, insert the new one and turn it clockwise until it locks, then flush about 2.5 gallons of water and hold the Water Filter button for 3 seconds to reset the indicator. Filter location and removal method vary by model, so check your owner's manual first.
When to Replace the Filter
LG says the water filter should be replaced about every 6 months. Debris builds up inside the cartridge over time, which reduces filtration performance and slows the water flow. You may also notice a change in the taste or odor of your water.
Your household's water usage and water quality may mean you need a new filter sooner than 6 months. LG advises checking the filter earlier if water dispenses slowly or the Water Filter Replacement indicator turns on.
- Replace about every 6 months
- Check sooner if flow slows or the indicator lights up
- Watch for changes in taste or odor
- 1Part on your old filterLG ADQ36006101Printed on the cartridge label
- 2Same part asLT700PAlso sold as ADQ36006101; ADQ36006102; Kenmore 46-9690
- 3ReplaceEvery 6 months or 200 gallonsSooner if flow slows or taste changes
- 4Before you orderMatch the part numberOn the box or listing: LT700P
Find the Right Filter First
Before you start, confirm which filter your refrigerator uses. Check the label on the existing filter, or use your refrigerator model number to look it up. LG lists common water filter models including LT500P, LT600P, LT700P, LT800P, LT900X3, and LT1000P.
LG notes that the water filter and the air filter, which removes odors inside the refrigerator, are different parts. If you are unsure which one you need, LG suggests using the Water and Air Filter Finder on its website with your model number. The filter's location and installation method depend on your specific refrigerator model.
Remove the Old Filter
LG's general guidance is to turn the old filter counterclockwise to remove it. Before you do, close the water supply valve connected to the refrigerator and press the dispenser paddle to drain any remaining water from the line. Place a towel or cup under the filter to catch drips and prevent slipping. Some models let you replace the filter without closing the valve, so check the owner's manual first.
The removal method varies by filter model. Here is how LG describes removal for several common types.
- LT500P: Remove the top shelf and move it to the lowest level. Press the tab under the lamp cover and pull it out toward the front. Turn the old filter left until the unlocked symbol lines up with the indicator line, then pull it down.
- LT600P: Rotate the knob of the cartridge counterclockwise. It will click out of place, then pull it out.
- LT700P: The housing is at the far back left inside the cabinet. Clear anything blocking its full range of motion, such as the top left shelf. Press the push button and pull downward, then gently pull toward you until the filter pops out. Some water may drain, so use a paper towel or cup.
- LT800P: Open the doors and remove the bottom door bin. Grab the bottom of the old filter and turn it counterclockwise to remove it from the filter head. On some models removal matches the LT700P, so follow that guide.
- LT900X3: Remove the filter cover on the left side of the fresh zone. Take out the left fresh zone drawer, push and pull out the bottom of the cover, turn the handle 90 degrees to the left, and pull forward.
- LT1000P: Open the doors and remove the bottom door bin. Turn the old filter counterclockwise to remove it from the filter head. On some models removal matches the LT700P, so follow that guide if yours looks different.
Install the New Filter
Unpack the new filter and remove the protective cap. Align the tabs on the filter with the slots in the housing and push it in completely. Then turn it clockwise until it is securely locked, making sure the lock mark lines up with the reference line.
Reinstall any covers, shelves, or door bins you removed. If the filter does not turn smoothly, LG says to pull it out, align it correctly, and push it straight in before turning it again.
Flush the System and Reset the Indicator
Slowly open the water supply valve and check for leaks. LG says to dispense approximately 2.5 gallons (9.5 liters) of water to remove trapped air and fine particles. LG's page also describes dispensing for 30 seconds, pausing for 60 seconds, and repeating for a total of 5 minutes.
Then press and hold the Water Filter or Filter Reset button on the control panel for 3 seconds. The reset is complete when you hear a chime or the indicator turns off.
If the water tastes unusual or contains air bubbles after replacement, LG says air may be trapped in the new filter or water line, and flushing about 2.5 gallons should clear it. If the problem continues, check that the filter is fully inserted and locked. Black particles right after replacement may be fine carbon particles from inside the filter. LG says these are harmless and will disappear once the filter is thoroughly flushed.
What to check for your model
Filter location, removal method, and reset button behavior vary by refrigerator model, and LG's page does not cover every filter type, including removal steps for the LT1000P. LG notes its guide is based on standard models and that settings menus may vary, so consult your owner's manual for your specific refrigerator.
Next step
- Use the filter finder to match your model number
- LG LT700P Filter: OEM vs Compatible
- Do You Need to Flush a New Refrigerator Water Filter? What Each Brand Says
- How we check filter matches
โ FAQ
Why does my water taste odd or have bubbles after replacing the filter?
LG says air may be trapped inside the new filter or the water line. Dispense approximately 2.5 gallons (9.5 liters) of water to flush the system. If the issue continues, make sure the filter is fully inserted and securely locked in place.
Why are there black particles in the water right after replacement?
LG says fine carbon particles from inside the filter may be released with the water, and these particles are harmless. Dispense approximately 2.5 gallons (9.5 liters) of water to flush the filter, and the particles should disappear once it is thoroughly flushed.
How do I know which filter my LG refrigerator needs?
Check the label on your existing filter, or use your refrigerator model number to find the correct replacement. LG lists common water filter models including LT500P, LT600P, LT700P, LT800P, LT900X3, and LT1000P, and offers a Water and Air Filter Finder on its website.
Sources
This article was written by the MatchMyFilter editorial team from manufacturer support pages. We do not run lab tests. As an Amazon Associate I earn from qualifying purchases.
More on this topic: Replacing a Refrigerator Water Filter: Steps, Timing and Aftercare
Related guides
Browse all refrigerator water filter guides
