MatchMyFilter is supported by readers. When you buy through our links we may earn a commission at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more›

Fridge Water Dispenses Slowly After Changing the Filter: Causes and Fixes

Part of our guide: Troubleshooting filter problems 📌 Key takeaways Trapped air is a common cause. Run water to purge...

📌 Key takeaways

  • Trapped air is a common cause. Run water to purge it first.
  • Check that the new filter is fully locked in.
  • To test whether the filter is the problem, GE suggests trying the bypass plug.
  • If it is still slow, low household water pressure may be the cause.

Water that sputters or trickles right after you change the filter is usually a sign of air in the line. Work through these steps in order. Exact volumes and steps vary by model, so your manual comes first.

  1. Purge the air

    Samsung’s troubleshooting page says to hold the dispenser for about 5 minutes, and that a steady stream can take 2 to 3 gallons. Treat that as an example and follow the instructions for your model. LG says sputtering water instead of a steady stream indicates air in the lines (Samsung, LG). Use short bursts and pauses if your manual says so. See also flushing a new filter.

  2. Check that the filter is seated

    Whirlpool says an improperly installed filter can reduce or stop water flow. Remove it, reinstall and lock it in.

  3. Check the part number

    A filter that is not the right one for your model may not seat correctly. Compare the number with your old cartridge or use the finder.

  4. Test without the filter

    GE suggests removing the filter and installing the bypass plug made for your refrigerator, then testing the dispenser. Bypass plugs are model-specific: for the XWFE system GE lists plug WR17X33825, which also has RFID (see our XWFE note). If flow improves, the filter may be clogged or defective. Samsung adds that if flow is fine without the filter but slow with a new one, the cause may be low water pressure. Not every fridge accepts a bypass plug, so check your manual.

  5. Look at the water supply

    Samsung says the refrigerator needs water pressure of at least 30 psi. Whirlpool notes that a kink in the line can reduce flow. If flow was fine before the change, the supply may be less likely to be the cause, but that is a possibility, not a diagnosis.

Stop and contact the manufacturer if the filter will not lock in, if anything leaks, or if water stops completely.

Close-up of a stainless steel refrigerator door with a water and ice dispenser
Example photo of a door dispenser. Slow flow right after a change is often trapped air. Photo by Julio Lopez on Unsplash

❔ FAQ

Is slow water after a change normal?

For a short time, yes, because of air. If it lasts after purging, something else is wrong.

Can a compatible filter cause slow flow?

If it is not seated or is not the right part, it can. We cannot say a compatible filter is slower in general.

Next step: See the XWFE filter page for the genuine part and the models it fits.

This article was written by the MatchMyFilter editorial team from manufacturer support pages and published standards. We do not run lab tests. As an Amazon Associate I earn from qualifying purchases.

Water dripping slowly from a tap
A trickle like this from the dispenser usually means air in the line, a filter not fully seated, or low water pressure. Photo by Walter Randlehoff on Unsplash

Find the right filter for your model

Filters are not interchangeable between brands. Look up your model first, then check the part number on the listing matches. Some common genuine filter codes: Use the filter finder to look up your model number.

Not sure which one you have? Our guide to finding your refrigerator model number shows where to look.

More on this topic: Refrigerator Water Filter Problems: Slow Water, Bad Taste, Fit and Light Issues

About the author

Ethan Marlowe
Ethan Marlowe

Ethan Marlowe is the Lead Technical Editor and Appliance Filtration Specialist at MatchMyFilter. He specializes in home appliance maintenance, water filtration mechanics, and independent verification of NSF/ANSI standards (NSF 42, 53, and 401) across major US refrigerator brands.